Position Paper-Hull Layup Techniques
Call the marina for details and stocking status or email us
Position Papers: Merc vs. Volvo * OMC Troubles * Hull Layup Techniques

This position paper is authored by Hoffmaster's Marina as a result of input from potential customers. It is NOT designed to be the final word, rather, it is an attempt at a conscientious and honest response to the most common issues in hopes of better-informing the consumer thus making him or her less vulnerable to misinformation.

Our Positions on Boat Construction:

Use of Plywood in boats: Many boat marketing departments are advertising the woodless boat. The fact is all boats use wood somewhere. In Cobalt's case it's hard to find but it's there in the latitudinal bulkheads. Some use wood in the transoms or to back up cushions. Lately consumers have been told that wood is bad. We at Hoffmaster's disagree strongly with this opinion for the following reasons:

Plywood has improved: In past times marine plywood was the best grade you could buy, and many builders used exterior AC instead of marine grade ply. For that reason and because the consumer was not properly trained in boat upkeep, the plywood would rot out over time. Today Chris Craft, Chaparral and Cobalt use XL Grade plywood wherever it is used. This plywood has a 10 year parts and labor guarantee and a lifetime parts guarantee. As with marine plywood XL has no voids which tend to promote decay. In addition, XL has upgraded adhesives binding the ply layers so it won't crumble.
Plywood is the best material to use in some cases: Especially on larger boats, plywood has the greatest strength for it's size in creating stringer grids. On cabin tops, manufacturers such as Sea Ray that depend solely on balsa coring to stiffen the deck end up with a lot of deflection. This springiness is troubling to the consumer to walk on. Plywood is the best material for backing large bustles or hatch cover and seats on sport boats because it doesn't warp. It's also necessary to use plywood under cockpit liners to keep them from feeling springy. It may even be the best transom core material because it takes stress and flexing well, unlike composites.
The grade of plywood makes a big difference: many manufacturers are still using lower grades of plywood! Those boats are vulnerable to all the rotting that took place in the past.

Chris Craft uses foam core stringers in it's boats up to 21', encapsulated XL stringers over 21'. Chris Craft uses XL in it's transoms, under some seat cushions, and under decks where stiffness is desirable. Plywood is also used for some cabin pods such as the galley. Most hatch covers and bustles use a composite, as do seat backs and mounts.
Chaparral's construction depends on the model:
All SSe models: XL floors and bustles, encapsulated XL stringers
Sunesta, 240, 245 SSi, Signature: encapsulated XL stringers, Fiberglass decking with some coring of plywood, plywood transoms
SSi 186,196,216,230,235: Composite transoms and most seats, fiberglass stringers. XL used in bustles, engine compartment vertical mounting brackets, some hatches

Layup/ Lamination
There are 4 types of fiberglass laminates used in our industry:
Mat, which is chopped fiberglass strands rolled into a sheet.
Woven Roving, which is a heavy bidirectional weave: *
Knits, which are more tightly weaved and come in bidirectional, tridirectional, and unidirectional patterns
Chopped strand which is sprayed through a chopper gun and mixed with resin in mid air

The rovings and cloths must be placed by hand after being soaked in polyester resin, thus earning the name "hand layup." This type of layup is much stronger than lesser boats that are totally laid up using chopped strand because chop strand, though tough, has no give to handle rough water and collision.
Chaparrals use Buffback gelcoat, which is a great gelcoat for blending repairs, followed by a vinylester blister prevention resin, followed by several layers of woven roving, mat, chopped strand, and tri directional roving. This creates a very strong hull.
Chris Crafts use the same gelcoat, a vinylester layer, and then a combination of all the knits, mat, and chopped strand. The knits are more expensive, but Chris Craft feels that less resin soaks into knits allowing a better ratio of glass to resin and better strength in all three dimensions.
Both layups create very strong hulls.

Back to  


 Boat buying tips! * Home * Used Boats * Links* Older CC Info * Parts and Service * Directions
E Mail Us
Hoffmaster's Marina
1214 Swan Point Rd.
Woodbridge, Va. 22192
703.494.7161
Fax 703.494.8786